Superior Quality｜ Other Products ｜Elasti-thane Membrane (5 Gallons)

Elasti-thane Membrane
Description
ELASTI-THANE BASECOAT is a high-solids, 2-component, amber/clear, aliphatic polyurethane coating designed to perform multiple functions. It provides the benefits of good UV resistance with the ability to be extended and applied at depths up to 2” when incorporating ROCK-TRED aggregates and fillers
Uses
ELASTI-THANE BASECOAT can be used the broadcast or slurry base coat in some ROCK-TRED SOFT-FLOOR Systems or a highly flexible joint filler. It can be extended up to 1:1 by volume with certain ROCK-TRED aggregates to make a slurry or flexible grout.
Typical Coverage
ELASTI-THANE BASECOAT can be installed as a grout up to 2 inches thick or as a high build component in flexible foot traffic membrane systems from 20 to 250 mils.
Physical Properties

Volume mix ratio
Mix entire content of kit

Viscosity [mixed]
4000-6000 CPS Typical

Solids Content [%]
96 % [ASTM D-2697]

Ultimate Elongation (ASTM D412)
1,000-1,200 %

Abrasion Resistance Tabor 1000 cycles / CS 17 wheel / 100g
0.02 grams Loss

Tensile Strength (ASTM D412)
700-800 psi

Hardness (ASTM C-661)
60-65 (Shore A)

Application Temps.
33° – 80° F

Potlife
35-40 minutes @ 75° F (24° C)

Recoat time
6-8 hours @ 75° F (24° C)

‘Open’ to foot traffic
12-16 hours @ 75° F (24° C)

‘Open’ to vehicle traffic
36+ hours @ 75° F (24° C)

Shelf Life
6 months in unopened unit

Limitations & For Best Results

ELASTI-THANE BASECOAT may be thinned up to 10% by volume with xylene for better flow and leveling.
Do not apply when work area exceeds 70% relative humidity or when substrate temperatures may fall to less than 5° F above dew point during the curing of the material.
Apply the next coat within 24 hours of completing the previous coat.
Do not apply directly to concrete. Use an appropriate ROCK-TRED Primer or basecoat system.
Do not apply this product heavier / thicker than the recommended spread rate / mil thickness.

Product Application
Apply using brush, roller and squeegee as a coating, or via gauge rake and spiked roller when applied as a slurry. When used as a joint filler or grout product may be poured or tooled into place. ROCK-TRED product test data is based on environmental temperatures of 75°F. Viscosity and working time are always affected by temperatures above or below that mark. When applying product – always consider the ambient, surface, and product temperature at the time and place of installation.
Color and Textures
ELASTI-THANE BASECOAT is available in amber/clear only but can be field pigmented using ROCK-TRED Universal Colorants. Use up to one Bag-Pak of Universal Colorant per 2.5-gallon mix. Most ROCK-TRED products are available in a wide range of textures using an appropriate aggregate.
Chemical Resistance
Always refer to ROCK-TRED’s chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.
Product Storage
DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50°F.
Surface Preparation
Always apply ROCK-TRED products to a clean / sound substrate that is free of laitance, grease, oils, debris and curing compounds. Make certain that concrete is properly dried and prepared before applying ROCK-TRED materials. Concrete substrates should be treated with the Rock-Block System when moisture testing per ASTM F2170 shows results over 80% RH. Whenever possible, remove existing coatings and/or flooring systems completely, if complete removal is not possible test to determine adhesion to the existing material. Mechanical preparation by means of shot-blasting or diamond grinding to a ICRI CSP 2/3/5 is the recommended preparation method (see ICRI Guideline No. 03732 for more information). If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.
Clean Up
Application tools and equipment can be cleaned with xylene immediately after use.
Disposal
Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.
Important Notice
Always read and acquaint yourself with ROCK-TRED’S Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your local representative or ROCK-TRED directly for recommendations.
Brand:Rock TredSKU:612G-5Tags:Polyurethane, Rock Tred